Semiconductor Wafer Handling

Precision Wafer Cassettes & Shipping Boxes Built for Your Process

25-slot PEEK, PFA and PP carriers engineered to SEMI dimensions — particle-controlled, ESD-safe and cleanroom-ready. Specify your wafer size, process temperature and automation interface; we deliver a qualified carrier, not a compromise.

  • ISO 9001 & CE certified
  • Free samples
  • Shipping to 40+ countries
  • Quote in 24 hours
Black ESD PEEK wafer cassettes and matching shipping box lids arranged for semiconductor wafer handling
25
Slots standard
250°C
PEEK service temp.
±0.1
mm slot tolerance
Specified by
  • Wafer fabs & foundries
  • Compound semiconductor lines
  • R&D and pilot lines
  • Power device & MEMS makers
Product range

Three carrier families, one qualified handling system

Choose the resin that matches your process — high-temperature PEEK, ultra-clean PFA, or cost-efficient PP for ambient storage and shipment. All three share the same slot geometry, so a wafer can move between them without re-teaching your tools.

25-slot black PEEK wafer cassette with matching PP shipping box, open and closed views High temperature

PEEK Wafer Cassette

25-slot carrier for 4″ and 6″ wafers. Holds slot geometry through hot DI water, acid benches and bake steps where PP creeps and warps.

  • 4″ / 6″Wafer size
  • 25Slots
  • 250°CContinuous use
  • ESD option104–1011 Ω
See full specifications
Six-inch photomask reticle shipping box in ESD ABS with latch closures, open and closed Transport

Wafer & Reticle Shipping Box

Rigid outer box with top and bottom lids that locks the cassette in place. ESD ABS body, particle-free foam-free interior, 24-month service life.

  • 4″ / 6″Cassette sizes
  • 6×6×0.25″Reticle format
  • ABS (ESD)Body material
  • 24 monthsService life
See full specifications
Stainless steel wafer cassette transfer station for moving wafers between PEEK and PFA cassettes Ultra clean

PFA Wafer Cassette

Translucent white PFA carrier for the most aggressive wet chemistries. Lowest extractables of the three resins, with visual inspection of every slot.

  • 25Slots
  • 260°CContinuous use
  • TranslucentVisual check
  • HF-readyChemistry
Ask for a data sheet
Performance

Engineered where a single particle is a defect

A carrier is not a container. It is a metrology reference, a chemical vessel and a robot interface at the same time. These are the six properties we design and inspect for.

Dimensional stability under heat

PEEK keeps its modulus and slot pitch to roughly 250 °C. Polypropylene starts to soften near 100 °C, so slots drift after a hot bath and wafers begin to touch. Our PEEK bodies are annealed after machining to release residual stress.

Low particle generation

Slot edges are radiused and polished, not sheared. Every part is ultrasonically cleaned in DI water, nitrogen-dried and particle-counted before it is bagged, so the carrier enters your line clean instead of being cleaned by your line.

ESD-safe, permanently

Conductive and dissipative compounds are bulk-loaded, not coated, so surface resistivity of 104–1011 Ω does not wash off or wear through. Essential for compound semiconductors, laser diodes and thin-film devices.

Broad chemical resistance

PEEK and PFA resist most acids, bases and solvents used in wafer cleaning. We will tell you where the limit is: concentrated HF attacks PEEK, so for that bath we quote PFA or PTFE instead of upselling the wrong resin.

Automation-compatible geometry

Robotic flange, bottom-pick and side-handle features can be added to the same body. Slot pitch and datum faces follow SEMI conventions for 100 mm and 150 mm wafers, so the cassette drops into existing load ports without re-teaching.

Measured, not claimed

Slot position, pitch, flatness and wafer seating are checked on a CMM and recorded per lot. You receive the inspection report with the shipment — a number you can put in your incoming quality file, not a brochure promise.

Material selection

Why PEEK replaces conventional PP carriers

Polypropylene made the semiconductor carrier affordable. It did not make it dimensionally stable.

PP softens at roughly 100 °C, creeps under load and sheds particles as it wears. In an ambient stocker that is acceptable. In a hot DI rinse, an acid bench, a bake step or a plasma-adjacent environment, the same carrier relaxes, slot pitch changes and wafers that were safely separated start to touch.

PEEK solves that specific failure. Its glass transition is about 143 °C and its continuous service temperature around 250 °C, so a cassette that leaves a 90 °C bath returns to the same dimensions it had before. Lower outgassing and lower wear debris follow from the same molecular structure.

Four reasons the switch pays for itself

  • Yield protection. Stable pitch means no cross-slot contact, the single largest cause of scratch-induced wafer loss in wet benches.
  • Carrier life. PEEK resists creep and chemical attack, so one cassette replaces several PP cassettes over the same period.
  • Fewer cleaning cycles. Lower particle shedding means less requalification and less downtime for the carrier itself.
  • Process window. One qualified carrier can move from ambient storage into a hot process, removing a transfer step and its handling risk.

When PP is the right answer: ambient storage, outgoing shipment and single-use logistics, where cost dominates and temperature never exceeds 60 °C. We supply both, and we will say so.

Resin comparison for wafer carriers
Property PP PEEK PFA
Continuous service temp.~100 °C~250 °C~260 °C
Glass transition (Tg)−10 °C143 °C−90 °C
Density0.90 g/cm³1.30 g/cm³2.15 g/cm³
Tensile strength~30 MPa~100 MPa~28 MPa
Creep resistance when hotPoorExcellentGood
Particle sheddingModerateLowVery low
OutgassingHigherLowLowest
Concentrated HFResistantNot recommendedResistant
Optical transparencyClearOpaqueTranslucent
Relative material cost1×15–25×8–12×
Best fitStorage, shipmentHot / aggressive processHF, ultra-clean wet

Typical unfilled resin values for comparison only. Actual figures depend on grade, filler and moulding. Certificates of analysis are supplied with each lot.

Industries

Where our carriers are in daily use

From 100 mm pilot lines to 200 mm production fabs, the same design rules apply: protect the front surface, keep the pitch, survive the chemistry.

Silicon fabs & foundries

In-process transport, wet bench handling, stocker storage and shipping of monitor wafers.

Compound semiconductors

GaAs, GaN, InP and SiC lines where ESD control and chemical inertness decide yield.

Power devices

IGBT, MOSFET and diode fabs handling thin, warped wafers that punish poor slot support.

MEMS & sensors

Small-die, high-mix runs needing frequent cassette changes and tight particle control.

R&D and institutes

Pilot lines and university cleanrooms that need small quantities and custom slot layouts.

Optics & photonics

Reticle and photomask storage, plus carriers for sapphire, quartz and glass substrates.

Field results

Two projects, measured at the customer's line

Names are withheld under NDA. Process data is reported exactly as the customer recorded it.

PEEK wafer cassette and shipping box set delivered for a 6-inch power device production line
Case 01 · Power devices

A 6-inch line stops losing wafers after a hot DI rinse

A power-device fab in eastern China was losing wafers to edge scratches after a 90 °C rinse followed by a 25-slot PP cassette transfer. Slot pitch on the PP carriers had drifted by 0.4 mm after three months in service.

We replaced the PP bodies with annealed 6-inch PEEK cassettes, keeping the existing outer boxes and load-port interface so no tooling change was needed. Slot pitch is now verified per lot at ±0.1 mm.

−92%Edge-scratch scraps
±0.1 mmVerified pitch
0Tool changes
ESD ABS reticle box used to ship 6 by 6 inch photomasks between two fabs
Case 02 · Photomask logistics

Shipping reticles between two fabs without a re-qualification

A photonics manufacturer moved 6″ × 6″ × 0.25″ masks between two sites every week. The previous wooden crate required a full inspection on arrival and consumed a cleanroom technician for half a day.

We supplied an ESD ABS reticle box with a positive latch and a moulded cavity that holds the mask off its patterned face. Arrival inspection dropped to a visual check, and the box has been in weekly rotation for 18 months.

18 moIn service
1/10Inspection time
0Mask rejects
Technical data

Specifications you can put in a purchase order

Dimensions below are from our controlled drawings. Tolerances, resin grade and surface finish can be tightened on request; tell us which value your process actually depends on.

4-inch PEEK wafer cassette, 25 slots
ParameterValue
Wafer size4 inch (Ø100 mm)
Slot count25
Slot pitch4.76 mm (3/16″), SEMI-compatible
Outside dimensions142.0 (L) × 125.5 (W) × 114.5 (H) mm
Weight356 g
Body materialPEEK, unfilled natural or ESD compound
ColourNatural tan / black (ESD)
Continuous service temperatureup to 250 °C
Slot position tolerance±0.10 mm
Surface resistivity (ESD grade)104 – 1011 Ω
Handling featuresRobot flange, side handles, bottom pick (option)
Matching outer boxPP shipping box with top and bottom lids
CleaningUltrasonic DI, nitrogen dry, particle count
PackingDouble bagged, cleanroom film, export carton

Dimensions are nominal for the catalogue part. Custom envelopes, slot counts and wafer sizes (including 8″ / 200 mm) are available — see custom manufacturing.

Custom manufacturing

Send the parameters. We build the carrier.

You do not need a finished 3D model. Six numbers and a description of your process are enough for us to start.

  • Wafer size and edge — diameter, notch or flat, thickness range.
  • Slot count and pitch — 13, 25, 50, or any custom spacing.
  • Envelope — maximum length, width and height your tool will accept.
  • Interface — robot flange, bottom pick, side handle, load-port datum.
  • Chemistry and temperature — the highest temperature and the worst bath.
  • ESD requirement — insulating, dissipative or conductive.

From that we return a DFM review, a material recommendation, a price and a lead time within 24–48 hours. Machined prototypes start at 10 pieces; moulded production becomes economic from roughly 500 pieces.

Share your parameters

Wafer size, slots, envelope, chemistry and interface. A sketch is enough.

DFM review & quote

We flag thin walls, draft angles and handling conflicts, then price it.

First article

Machined sample with a CMM report for fit check on your tool.

Production & QC

Moulding or machining, 100% dimensional and particle inspection.

Typical lead times

Catalogue sample3–7 working days
Custom machined sample10–15 working days
New injection mould25–35 days
Production run15–25 days after approval
About Xinkehui

A materials company that happens to make carriers

Shanghai Xinkehui New Materials Co., Ltd. develops and manufactures semiconductor materials and handling hardware — sapphire substrates, silicon and silicon carbide wafers, quartz and ZnSe optics, and the polymer carriers that move wafers between process steps.

We started on the materials side, which is why our carriers are specified by resin grade and measured by dimension rather than described by adjective. Our engineering team works directly with fab process engineers: if a cassette fails, we want the bath temperature, the soak time and the particle map, not a purchase order for a replacement.

Manufacturing is based in Shanghai with partner production in Xiamen, and we ship to customers across Asia, Europe and North America. Every order leaves with a dimensional inspection report, a material certificate and a lot number that can be traced back to the resin batch.

12+
Patents granted
40+
Countries served
24h
Quote turnaround

Certifications & honours

National High-Tech Enterprise
Recognised for in-house R&D in semiconductor materials
Invention patents
12+ granted, including resin formulation and carrier design
ISO 9001 quality system
Documented incoming, in-process and final inspection
CE & RoHS / REACH
Equipment marked for EU supply; material declarations on request

Certificates are available as scanned copies for your supplier qualification file — ask us and we will send the current versions.

Inside the operation

Capability overview — photographs of our Shanghai and Xiamen facilities are supplied on request and during customer audits.

Machining
CNC & PEEK machining
3-axis and 4-axis centres, annealed stress relief
Moulding
Injection moulding
25-slot tooling for 4″, 6″ and 8″ bodies
Metrology
CMM & slot gauging
Pitch, flatness and seating verified per lot
Cleanroom
Wash & packing
Ultrasonic DI, N₂ dry, particle count, double bag

Talk to an engineer, not a call centre

Send your drawing or your process description and you will get a technical reply — including where a PEEK cassette is the wrong choice.

Contact the technical team
Service & after-sales

Terms that remove the risk from a first order

Carrier qualification is slow enough already. These are the commitments we make so that trying us costs you time, not money.

Free samples

Standard catalogue cassettes and boxes, free of charge for qualified customers. You pay freight only.

Freight refunded

Sample freight is credited against your first production order, so evaluation ends up costing nothing.

Free replacement

Any dimensional or material defect within 30 days: replacement or refund, return freight on us.

24-hour response

Technical questions answered within one working day, in English or Chinese, by the engineer handling your file.

Visit us in Shanghai

Customers audit our line before they qualify a carrier, and we prefer it that way. Walk the machining floor, watch a CMM run, and open a random carton from stock. Visits can be arranged at our Shanghai office and the Xiamen production site — tell us your dates and we will plan the schedule, including pickup from Pudong or Hongqiao.

120+Customer visits / year
2Sites to audit
FAQ

Questions engineers actually ask

Fourteen answers on material choice, dimensions, cleaning and logistics. If yours is not here, send it — we answer technical questions whether or not you buy.

Ask a question
What is a wafer cassette used for?

A cassette is a slotted carrier that holds wafers upright and separated during transport, storage and wet processing. Each slot keeps a fixed pitch so wafers never touch, protecting the polished front surface and edges from scratches, particles and cross-contamination.

Why choose a PEEK cassette instead of PP?

PEEK holds its dimensions and stiffness to about 250 °C, while polypropylene softens near 100 °C. That means no slot creep after hot DI water, acid or bake steps, plus lower particle shedding and outgassing. For ambient storage and shipping, PP is still the cost-effective choice — we supply both.

Do you offer 25-slot cassettes for 4-inch and 6-inch wafers?

Yes. Standard tooling covers 25-slot 4-inch (100 mm) and 6-inch (150 mm) cassettes, and we also produce 200 mm and custom-pitch versions. Standard pitch is 4.76 mm for 4-inch and 6.35 mm for 6-inch wafers.

Are your cassettes ESD safe?

We supply insulating natural PEEK and permanently conductive or dissipative compounds with surface resistivity of 104–1011 Ω. The additive is in the bulk resin, so performance does not wear off. ESD grades are recommended for compound semiconductors and laser diodes.

Can you manufacture a custom cassette from our drawing?

Yes. Send wafer size, slot count, pitch, envelope, robot or load-port interface, and the chemicals and temperatures involved. We return a DFM review and quotation in 24–48 hours, then produce a first article for approval before mass production.

What is the minimum order quantity?

Catalogue 4-inch and 6-inch PEEK cassettes typically start at 50 pieces. Custom machined designs start from 10 pieces. Evaluation samples of one to five pieces are available.

How long does a sample take?

Catalogue samples ship in 3–7 working days. Custom machined samples take 10–15 working days after drawing approval. A new injection mould takes 25–35 days.

Are samples free?

Yes — standard catalogue items are free for qualified customers; you cover courier freight, which we credit against your first production order.

How are the cassettes cleaned and packed?

Every part is ultrasonically cleaned in DI water, nitrogen-dried, dimensionally inspected and particle-counted, then double-bagged in cleanroom film inside an export carton. Class 100 cleanroom bagging is available on request.

What temperatures can the cassette withstand?

Unfilled PEEK serves continuously around 250 °C, with a glass transition near 143 °C and melting near 343 °C. PFA is rated to about 260 °C with lower extractables. PP should stay below roughly 100 °C.

Can the cassette be used with HF or strong oxidisers?

PEEK resists most acids, bases and solvents but is attacked by concentrated hydrofluoric acid and some strong oxidisers. For concentrated HF, choose PFA or PTFE. Tell us your chemistry and we will recommend the right resin instead of the most expensive one.

Do you ship internationally and what are the terms?

We ship worldwide from Shanghai by express, air and sea. Terms are typically EXW, FOB Shanghai or DDP by negotiation. Export documents, material certificates and inspection reports accompany every shipment.

What is your warranty and return policy?

We replace or refund any part with a dimensional or material defect within 30 days of delivery, and cover return freight when the fault is ours. Custom parts are covered against deviation from the approved drawing.

Can you supply the matching shipping box and lid?

Yes. The 25-slot PP shipping box with top and bottom lids is sized for 4-inch and 6-inch cassettes, with ESD and cleanroom bagging options, so cassette and outer box arrive as one qualified set.

Next step

Get a carrier recommendation, not a catalogue

Tell us your wafer size, process temperature and chemistry. We will tell you which resin survives it, what it costs, and how fast it can ship.

Contact

Send your specification

Attach nothing and write three lines — that is enough to start. For drawings, email us directly and we will reply with a DFM review.

For faster quoting, include:

  • Wafer size, slot count and pitch
  • Maximum process temperature and chemicals
  • Annual quantity and required delivery date

Submitting opens WhatsApp with your details pre-filled so the message reaches an engineer immediately. Prefer email? Write to [email protected]. We never share your data.